0 |
PLEASE TURN OFF POWER |
1 |
TH PARITY ALARM |
2 |
TV PARITY ALARM |
3 |
TOO MANY DIGITS |
4 |
ADDRESS NOT FOUND |
5 |
NO DATA AFTER ADDRESS |
6 |
ILLEGAL USE OF NEGATIVE SIGN |
7 |
ILLEGAL USE OF DECIMAL POINT |
9 |
ILLEGAL ADDRESS INPUT |
10 |
IMPROPER G–CODE |
11 |
NO FEEDRATE COMMANDED |
14 |
CAN NOT COMMAND G95 (M series) |
14 |
ILLEGAL LEAD COMMAND (T series) |
15 |
TOO MANY AXES COMMANDED (M series) |
15 |
TOO MANY AXES COMMANDED (T series) |
20 |
OVER TOLERANCE OF RADIUS |
21 |
ILLEGAL PLANE AXIS COMMANDED |
22 |
NO CIRCLE RADIUS |
23 |
ILLEGAL RADIUS COMMAND (T series) |
25 |
CANNOT COMMAND F0 IN G02/G03 (M series) |
27 |
NO AXES COMMANDED IN G43/G44 (M series) |
28 |
ILLEGAL PLANE SELECT |
29 |
ILLEGAL OFFSET VALUE (M series) |
29 |
ILLEGAL OFFSET VALUE (T series) |
30 |
ILLEGAL OFFSET NUMBER (M series) |
30 |
ILLEGAL OFFSET NUMBER (T series) |
31 |
ILLEGAL P COMMAND IN G10 |
32 |
ILLEGAL OFFSET VALUE IN G10 |
33 |
NO SOLUTION AT CRC (M series) |
33 |
NO SOLUTION AT CRC (T series) |
34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (M series) |
34 |
NO CIRC ALLOWED IN ST–UP /EXT BLK (T series) |
35 |
CAN NOT COMMANDED G31 (T series) |
35 |
CAN NOT COMMANDED G39 (M series) |
36 |
CAN NOT COMMANDED G31 (M series) |
37 |
CAN NOT CHANGE PLANE IN CRC (M seires) |
37 |
CAN NOT CHANGE PLANE IN NRC (T seires) |
38 |
INTERFERENCE IN CIRCULAR BLOCK (M seires) |
38 |
INTERFERENCE IN CIRCULAR BLOCK (T series) |
39 |
CHF/CNR NOT ALLOWED IN NRC (T series) |
40 |
INTERFERENCE IN G90/G94 BLOCK (T series) |
41 |
INTERFERENCE IN CRC (M seires) |
41 |
INTERFERENCE IN NRC (T seires) |
42 |
G45/G48 NOT ALLOWED IN CRC (M series) |
44 |
G27–G30 NOT ALLOWED IN FIXED CYC (M series) |
45 |
ADDRESS Q NOT FOUND (G73/G83) (M series) |
46 |
ILLEGAL REFERENCE RETURN COMMAND |
47 |
ILLEGAL AXIS SELECT |
48 |
BASIC 3 AXIS NOT FOUND |
49 |
ILLEGAL OPERATION (G68/G69) (M series) |
50 |
CHF/CNR NOT ALLOWED IN THRD BLK (M series) |
50 |
CHF/CNR NOT ALLOWED IN THRD BLK(T series) |
51 |
MISSING MOVE AFTER CHF/CNR (M series) |
51 |
MISSING MOVE AFTER CHF/CNR (T series) |
52 |
CODE IS NOT G01 AFTER CHF/CNR (M series) |
52 |
CODE IS NOT G01 AFTER CHF/CNR (T series) |
53 |
TOO MANY ADDRESS COMMANDS (M series) |
53 |
TOO MANY ADDRESS COMMANDS (T seires) |
54 |
NO TAPER ALLOWED AFTER CHF/CNR (T series) |
55 |
MISSING MOVE VALUE IN CHF/CNR (M series) |
55 |
MISSING MOVE VALUE IN CHF/CNR (T series) |
56 |
NO END POINT & ANGLE IN CHF/CNR (T series) |
57 |
NO SOLUTION OF BLOCK END (T series) |
58 |
END POINT NOT FOUND (M series) |
58 |
END POINT NOT FOUND (T series) |
59 |
PROGRAM NUMBER NOT FOUND |
60 |
SEQUENCE NUMBER NOT FOUND |
61 |
ADDRESS P/Q NOT FOUND IN G70–G73 (T series) |
62 |
ILLEGAL COMMAND IN G71–G76 (T series) |
63 |
SEQUENCE NUMBER NOT FOUND (T series) |
64 |
SHAPE PROGRAM NOT MONOTONOUSLY (T series) |
65 |
ILLEGAL COMMAND IN G71–G73 (T series) |
66 |
IMPROPER G–CODE IN G71–G73 (T series) |
67 |
CAN NOT ERROR IN MDI MODE (T series) |
69 |
FORMAT ERROR IN G70–G73 (T series) |
70 |
NO PROGRAM SPACE IN MEMORY |
71 |
DATA NOT FOUND |
72 |
TOO MANY PROGRAMS |
73 |
PROGRAM NUMBER ALREADY IN |
74 |
ILLEGAL PROGRAM NUMBER |
75 |
PROTECT |
76 |
ADDRESS P NOT DEFINED |
77 |
SUB PROGRAM NESTING ERROR |
78 |
NUMBER NOT FOUND |
79 |
PROGRAM VERIFY ERROR |
80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (M series) |
80 |
G37 ARRIVAL SIGNAL NOT ASSERTED (T series) |
81 |
OFFSET NUMBER NOT FOUND IN G37 (M series) |
81 |
OFFSET NUMBER NOT FOUND IN G37 (T series) |
82 |
H–CODE NOT ALLOWED IN G37 (M series) |
82 |
T–CODE NOT ALLOWED IN G37 (T series) |
83 |
ILLEGAL AXIS COMMAND IN G37 (M series) |
83 |
ILLEGAL AXIS COMMAND IN G37 (T series) |
85 |
COMMUNICATION ERROR |
86 |
DR SIGNAL OFF |
87 |
BUFFER OVERFLOW |
88 |
LAN FILE TRANS ERROR (CHANNEL–1) |
89 |
LAN FILE TRANS ERROR (CHANNEL–2) |
90 |
REFERENCE RETURN INCOMPLETE |
91 |
REFERENCE RETURN INCOMPLETE |
92 |
AXES NOT ON THE REFERENCE POINT |
94 |
P TYPE NOT ALLOWED (COORD CHG) |
95 |
P TYPE NOT ALLOWED (EXT OFS CHG) |
96 |
P TYPE NOT ALLOWED (WRK OFS CHG) |
97 |
P TYPE NOT ALLOWED (AUTO EXEC) |
98 |
G28 FOUND IN SEQUENCE RETURN |
99 |
MDI EXEC NOT ALLOWED AFT. SEARCH |
100 |
PARAMETER WRITE ENABLE |
101 |
PLEASE CLEAR MEMORY |
109 |
FORMAT ERROR IN G08 (M series) |
110 |
DATA OVERFLOW |
111 |
CALCULATED DATA OVERFLOW |
112 |
DIVIDED BY ZERO |
113 |
IMPROPER COMMAND |
114 |
FORMAT ERROR IN MACRO |
115 |
ILLEGAL VARIABLE NUMBER |
116 |
WRITE PROTECTED VARIABLE |
118 |
PARENTHESIS NESTING ERROR |
119 |
ILLEGAL ARGUMENT |
122 |
FOUR FOLD MACRO MODAL–CALL |
123 |
CAN NOT USE MACRO COMMAND IN DNC |
124 |
MISSING END STATEMENT |
125 |
FORMAT ERROR IN MACRO |
126 |
ILLEGAL LOOP NUMBER |
127 |
NC, MACRO STATEMENT IN SAME BLOCK |
128 |
ILLEGAL MACRO SEQUENCE NUMBER |
129 |
ILLEGAL ARGUMENT ADDRESS |
130 |
ILLEGAL AXIS OPERATION |
131 |
TOO MANY EXTERNAL ALARM MESSAGES |
132 |
ALARM NUMBER NOT FOUND |
133 |
ILLEGAL DATA IN EXT. ALARM MSG |
135 |
ILLEGAL ANGLE COMMAND (M series) |
135 |
SPINDLE ORIENTATION PLEASE (T series) |
136 |
C/H–CODE & MOVE CMD IN SAME BLK. (T series) |
136 |
ILLEGAL AXIS COMMAND (M series) |
137 |
M–CODE & MOVE CMD IN SAME BLK. |
138 |
SUPERIMPOSED DATA OVERFLOW |
139 |
CAN NOT CHANGE PMC CONTROL AXIS |
141 |
CAN NOT COMMAND G51 IN CRC (M series) |
142 |
ILLEGAL SCALE RATE (M series) |
143 |
SCALED MOTION DATA OVERFLOW (M series) |
144 |
ILLEGAL PLANE SELECTED (M series) |
145 |
ILLEGAL CONDITIONS IN POLAR COORDINATE INTERPOLATION |
146 |
IMPROPER G CODE |
148 |
ILLEGAL SETTING DATA (M series) |
149 |
FORMAT ERROR IN G10L3 (M series) |
150 |
ILLEGAL TOOL GROUP NUMBER |
151 |
TOOL GROUP NUMBER NOT FOUND |
152 |
NO SPACE FOR TOOL ENTRY |
153 |
T–CODE NOT FOUND |
154 |
NOT USING TOOL IN LIFE GROUP (M series) |
155 |
ILLEGAL T–CODE IN M06 (M series) |
155 |
ILLEGAL T–CODE IN M06 (T series) |
156 |
P/L COMMAND NOT FOUND |
157 |
TOO MANY TOOL GROUPS |
158 |
ILLEGAL TOOL LIFE DATA |
159 |
TOOL DATA SETTING INCOMPLETE |
163 |
COMMAND G68/G69 INDEPENDENTLY T series (At two–path) |
175 |
ILLEGAL G107 COMMAND |
176 |
IMPROPER G–CODE IN G107 (M series) |
176 |
IMPROPER G–CODE IN G107 (T series) |
177 |
CHECK SUM ERROR (G05 MODE) |
178 |
G05 COMMANDED IN G41/G42 MODE |
179 |
PARAM. (NO. 7510) SETTING ERROR |
180 |
COMMUNICATION ERROR (REMOTE BUF) |
181 |
FORMAT ERROR IN G81 BLOCK (Hobbing machine, EGB) (M series) |
182 |
G81 NOT COMMANDED (Hobbing machine) (M series) |
183 |
DUPLICATE G83 (COMMANDS) (Hobbing machine) (M series) |
184 |
ILLEGAL COMMAND IN G81 (Hobbing machine, EGB) (M series) |
185 |
RETURN TO REFERENCE POINT (Hobbing machine) (M series) |
186 |
PARAMETER SETTING ERROR (Hobbing machine, EGB) (M series) |
187 |
HOB COMMAND IS NOT ALLOWED |
190 |
ILLEGAL AXIS SELECT (M series) |
194 |
SPINDLE COMMAND IN SYNCHRO–MODE |
195 |
MODE CHANGE ERROR |
197 |
C–AXIS COMMANDED IN SPINDLE MODE |
199 |
MACRO WORD UNDEFINED |
200 |
ILLEGAL S CODE COMMAND |
201 |
FEEDRATE NOT FOUND IN RIGID TAP |
202 |
POSITION LSI OVERFLOW |
203 |
PROGRAM MISS AT RIGID TAPPING |
204 |
ILLEGAL AXIS OPERATION |
205 |
RIGID MODE DI SIGNAL OFF |
206 |
CAN NOT CHANGE PLANE (RIGID TAP) (M series) |
207 |
RIGID DATA MISMATCH |
210 |
CAN NOT COMAND M198/M199 |
211 |
G31 (HIGH) NOT ALLOWED IN G99 |
212 |
ILLEGAL PLANE SELECT (M series) |
212 |
ILLEGAL PLANE SELECT (T series) |
213 |
ILLEGAL COMMAND IN SYNCHRO–MODE |
213 |
ILLEGAL COMMAND IN SYNCHRO–MODE (T series) |
214 |
ILLEGAL COMMAND IN SYNCHRO–MODE |
217 |
DUPLICATE G51.2 (COMMANDS) (T series) |
218 |
NOT FOUND P/Q COMMAND IN G251 (T series) |
219 |
COMMAND G250/G251 INDEPENDENTLY (T series) |
220 |
ILLEGAL COMMAND IN SYNCHR–MODE (T series) |
221 |
ILLEGAL COMMAND IN SYNCHR–MODE (T series) |
222 |
DNC OP. NOT ALLOWED IN BG.–EDIT (M series) |
224 |
RETURN TO REFERENCE POINT (M series) |
224 |
RETURN TO REFERENCE POINT (T series) |
225 |
SYNCHRONOUS/MIXED CONTROL ERROR (T series (At two–path)) |
226 |
ILLEGAL COMMAND IN SYNCHRO– MODE (T series (At two–path)) |
229 |
CAN NOT KEEP SYNCHRO–STATE (T series) |
230 |
R CODE NOT FOUND (Grinding machine) (M series) |
231 |
ILLEGAL FORMAT IN G10 OR L50 |
233 |
DEVICE BUSY |
239 |
BP/S ALARM |
240 |
BP/S ALARM |
244 |
P/S ALARM (T series) |
245 |
T–CODE NOT ALOWEE IN THIS BLOCK (T series) |
251 |
ATC ERROR (M series) |
252 |
ATC SPINDLE ALARM (M series) |
253 |
G05 IS NOT AVAILABLE (M series) |
300 |
n AXIS NEED ZRN |
301 |
APC ALARM:n AXIS COMMUNICATION |
302 |
APC ALARM:n AXIS OVER TIME |
303 |
APC ALARM:n AXIS FRAMING |
304 |
APC ALARM:n AXIS PARITY |
305 |
APC ALARM:n AXIS PULSE MISS |
306 |
APC ALARM:n AXIS BATTERY ZERO |
307 |
APC ALARM:n AXIS BATTERY DOWN 1 |
308 |
APC ALARM:n AXIS BATTERY DOWN 2 |
309 |
APC ALARM:n AXIS ZRN IMPOSSIBLE |
360 |
n AXIS : ABNORMAL CHECKSUM (INT) |
361 |
n AXIS : ABNORMAL PHASE DATA (INT) |
362 |
n AXIS : ABNORMAL REV.DATA (INT) |
363 |
n AXIS : ABNORMAL CLOCK (INT) |
364 |
n AXIS : SOFT PHASE ALARM (INT) |
365 |
n AXIS : BROKEN LED (INT) |
366 |
n AXIS : PULSE MISS (INT) |
367 |
n AXIS : COUNT MISS (INT) |
368 |
n AXIS : SERIAL DATA ERROR (INT) |
369 |
n AXIS : DATA TRANS. ERROR (INT) |
380 |
n AXIS : BROKEN LED (EXT) |
381 |
n AXIS : ABNORMAL PHASE (EXT LIN) |
382 |
n AXIS : COUNT MISS (EXT) |
383 |
n AXIS : PULSE MISS (EXT) |
384 |
n AXIS : SOFT PHASE ALARM (EXT) |
385 |
n AXIS : SERIAL DATA ERROR (EXT) |
386 |
n AXIS : DATA TRANS. ERROR (EXT) |
387 |
n AXIS : ABNORMAL ENCODER (EXT) |
400 |
SERVO ALARM: n–TH AXIS OVERLOAD |
401 |
SERVO ALARM: n–TH AXIS VRDY OFF |
402 |
SERVO ALARM: SV CARD NOT EXIST |
403 |
SERVO ALARM: CARD/SOFT MISMATCH |
404 |
SERVO ALARM: n–TH AXIS VRDY ON |
405 |
SERVO ALARM: (ZERO POINT RETURN FAULT) |
407 |
SERVO ALARM: EXCESS ERROR |
409 |
SERVO ALARM: n AXIS TORQUE ALM |
410 |
SERVO ALARM: n–TH AXIS – EXCESS ERROR |
411 |
SERVO ALARM: n–TH AXIS – EXCESS ERROR |
413 |
SERVO ALARM: n–th AXIS – LSI OVERFLOW |
414 |
SERVO ALARM: n–TH AXIS – DETECTION RELATED ERROR |
415 |
SERVO ALARM: n–TH AXIS – EXCESS SHIFT |
416 |
SERVO ALARM: n–TH AXIS – DISCONNECTION |
417 |
SERVO ALARM: n–TH AXIS – PARAMETER INCORRECT |
420 |
SERVO ALARM: n AXIS SYNC TORQUE (M series) |
421 |
SERVO ALARM: n AXIS EXCESS ER (D) |
422 |
SERVO ALARM: n AXIS |
423 |
SERVO ALARM: n AXIS |
430 |
n AXIS : SV. MOTOR OVERHEAT |
431 |
n AXIS : CNV. OVERLOAD |
432 |
n AXIS : CNV. LOW VOLT CONTROL |
433 |
n AXIS : CNV. LOW VOLT DC LINK |
434 |
n AXIS : INV. LOW VOLT CONTROL |
435 |
n AXIS : INV. LOW VOLT DC LINK |
436 |
n AXIS : SOFTTHERMAL (OVC) |
437 |
n AXIS : CNV. OVERCURRENT POWER |
438 |
n AXIS : INV. ABNORMAL CURRENT |
439 |
n AXIS : CNV. OVER VOLT DC LINK |
440 |
n AXIS : CNV. EX DECELERATION POW. |
441 |
n AXIS : ABNORMAL CURRENT OFFSET |
442 |
n AXIS : CNV. CHARGE FAILURE |
443 |
n AXIS : CNV. COOLING FAN FAILURE |
444 |
n AXIS : INV. COOLING FAN FAILURE |
445 |
n AXIS : SOFT DISCONNECT ALARM |
446 |
n AXIS : HARD DISCONNECT ALARM |
447 |
n AXIS : HARD DISCONNECT (EXT) |
448 |
n AXIS : UNMATCHED FEEDBACK ALARM |
449 |
n AXIS : INV. IPM ALARM |
453 |
n AXIS : SPC SOFT DISCONNECT ALARM |
456 |
n AXIS : ILLEGAL CURRENT LOOP |
457 |
n AXIS : ILLEGAL HI HRV (250US) |
458 |
n AXIS : CURRENT LOOP ERROR |
459 |
n AXIS : HI HRV SETTING ERROR |
460 |
n AXIS : FSSB DISCONNECT |
461 |
n AXIS : ILLEGAL AMP INTERFACE |
462 |
n AXIS : SEND CNC DATA FAILED |
463 |
n AXIS : SEND SLAVE DATA FAILED |
464 |
n AXIS : WRITE ID DATA FAILED |
465 |
n AXIS : READ ID DATA FAILED |
466 |
n AXIS : MOTOR/AMP COMBINATION |
467 |
n AXIS : ILLEGAL SETTING OF AXIS |
468 |
n AXIS : HI HRV SETTING ERROR (AMP) |
500 |
OVER TRAVEL : +n |
501 |
OVER TRAVEL : –n |
502 |
OVER TRAVEL : +n |
503 |
OVER TRAVEL : –n |
504 |
OVER TRAVEL : +n |
505 |
OVER TRAVEL : –n |
506 |
OVER TRAVEL : +n |
507 |
OVER TRAVEL : –n |
700 |
OVERHEAT: CONTROL UNIT |
701 |
OVERHEAT: FAN MOTOR |
704 |
OVERHEAT: SPINDLE |
740 |
RIGID TAP ALARM : EXCESS ERROR |
741 |
RIGID TAP ALARM : EXCESS ERROR |
742 |
RIGID TAP ALARM : LSI OVER FLOW |
749 |
S–SPINDLE LSI ERROR |
750 |
SPINDLE SERIAL LINK START FAULT |
751 |
FIRST SPINDLE ALARM DETECTION (AL–XX) |
752 |
FIRST SPINDLE MODE CHANGE FAULT |
754 |
SPINDLE–1 ABNORMAL TORQUE ALM |
761 |
SECOND SPINDLE ALARM DETECTION (AL–XX) |
762 |
SECOND SPINDLE MODE CHANGE FAULT |
764 |
SPINDLE–2 ABNORMAL TORQUE ALM |
771 |
SPINDLE–3 ALARM DETECT (AL–XX) |
772 |
SPINDLE–3 MODE CHANGE ERROR |
774 |
SPINDLE–3 ABNORMAL TORQUE ALM |
782 |
SPINDLE–4 MODE CHANGE ERROR |
784 |
SPINDLE–4 ABNORMAL TORQUE ALM |
900 |
ROM PARITY |
910 |
SRAM PARITY : (BYTE 0) |
911 |
SRAM PARITY : (BYTE 1) |
912 |
DRAM PARITY : (BYTE 0) |
913 |
DRAM PARITY : (BYTE 1) |
914 |
DRAM PARITY : (BYTE 2) |
915 |
DRAM PARITY : (BYTE 3) |
916 |
DRAM PARITY : (BYTE 4) |
917 |
DRAM PARITY : (BYTE 5) |
918 |
DRAM PARITY : (BYTE 6) |
919 |
DRAM PARITY : (BYTE 7) |
920 |
SERVO ALARM (1–4 AXIS) |
921 |
SERVO ALARM (5–8 AXIS) |
926 |
FSSB ALARM |
930 |
CPU INTERRUPUT |
935 |
SRAM ECC ERROR |
950 |
PMC SYSTEM ALARM |
951 |
PMC WATCH DOG ALARM |
970 |
NMI OCCURRED IN PMCLSI |
971 |
NMI OCCURRED IN SLC |
972 |
NMI OCCURRED IN OTHER MODULE |
973 |
NON MASK INTERRUPT |
974 |
F–BUS ERROR |
975 |
BUS ERROR |
976 |
L–BUS ERROR |
4500 |
REPOSITIONING INHIBITED |
4502 |
ILLEGAL COMMAND IN BOLT HOLE |
4503 |
ILLEGAL COMMAND IN LINE AT ANGLE |
4504 |
ILLEGAL COMMAND IN ARC |
4505 |
ILLEGAL COMMAND IN GRID |
4506 |
ILLEGAL COMMAND IN SHARE PROOFS |
4507 |
ILLEGAL COMMAND IN SQUARE |
4508 |
ILLEGAL COMMAND IN RADIUS |
4509 |
ILLEGAL COMMAND IN CUT AT ANGLE |
4510 |
ILLEGAL COMMAND IN LINE-PUNCH |
4511 |
ILLEGAL COMMAND IN CIRCLE-PUNCH |
4520 |
T, M INHIBITED IN NIBBLING-MODE |
4521 |
EXCESS NIBBLING MOVEMENT (X, Y) |
4522 |
EXCESS NIBBLING MOVEMENT (C) |
4523 |
ILLEGAL COMMAND IN CIRCLE-NIBBL |
4524 |
ILLEGAL COMMAND IN LINE-NIBBL |
4530 |
A/B MACRO NUMBER ERROR |
4531 |
U/V MACRO FORMAT ERROR |
4532 |
IMPROPER U/V MACRO NUMBER |
4533 |
U/V MACRO MEMORY OVERFLOW |
4534 |
W MACRO NUMBER NOT FOUND |
4535 |
U/V MACRO NESTING ERROR |
4536 |
NO W, Q COMMAND IN MULTI-PIECE |
4537 |
ILLEGAL Q VALUE IN MULTI-PIECE |
4538 |
W NO. NOT FOUND IN MULTI-PIECE |
4539 |
MULTI-PIECE SETTING IS ZERO |
4540 |
MULTI-PIECE COMMAND WITHIN MACRO |
4542 |
MULTI-PIECE COMMAND ERROR |
4543 |
MULTI-PIECE Q COMMAND ERROR |
4544 |
MULTI-PIECE RESTART ERROR |
4549 |
ILLEGAL TOOL DATA FORMAT |
4600 |
T, C COMMAND IN INTERPOLATION |
4601 |
INHIBITED T, M COMMAND |
4602 |
ILLEGAL T-CODE |
4603 |
C AXIS SYNCHRONOUS ERROR |
4604 |
ILLEGAL AXIS OPERATION |
4605 |
NEED ZRN |
4630 |
ILLEGAL COMMAND IN LASER MODE |
4650 |
IMPROPER G-CODE IN OFFSET MODE |
4700 |
PROGRAM ERROR (OT +) |
4701 |
PROGRAM ERROR (OT –) |
4702 |
PROGRAM ERROR (OT +) |
4703 |
PROGRAM ERROR (OT –) |
4704 |
PROGRAM ERROR (OT +) |
4705 |
PROGRAM ERROR (OT –) |
4815 |
ZONE : ENTERING INHIBITED 3 –X |
5000 |
ILLEGAL COMMAND CODE (M series) |
5003 |
ILLEGAL PARAMETER (HPCC) (M series) |
5004 |
HPCC NOT READY |
5006 |
TOO MANY WORD IN ONE BLOCK (M series) |
5007 |
TOO LARGE DISTANCE (M series) |
5009 |
PARAMETER ZERO (DRY RUN) (M series) |
5010 |
END OF RECORD |
5012 |
G05 P10000 ILLEGAL START UP (HPCC) (M series) |
5013 |
HPCC: CRC OFS REMAIN AT CANCEL (M series) |
5014 |
TRACE DATA NOT FOUND (M series) |
5018 |
POLYGON SPINDLE SPEED ERROR (T series) |
5020 |
PARAMETER OF RESTART ERROR |
5030 |
ILLEGAL COMMAND (G100) (T series) |
5031 |
ILLEGAL COMMAND (G100, G102, G103) (T series) |
5032 |
NEW PRG REGISTERED IN B–AXS MOVE (T series) |
5033 |
NO PROG SPACE IN MEMORY B–AXS (T series) |
5034 |
PLURAL COMMAND IN G110 (T series) |
5035 |
NO FEEDRATE COMMANDED B–AXS (T series) |
5036 |
ADDRESS R NOT DEFINED IN G81–G86 (T series) |
5037 |
ADDRESS Q NOT DEFINED IN G83 (T series) |
5038 |
TOO MANY START M–CODE COMMAND (T series) |
5039 |
START UNREGISTERED B–AXS PROG (T series) |
5040 |
CAN NOT COMMANDED B–AXS MOVE (T series) |
5041 |
CAN NOT COMMANDED G110 BLOCK (T series) |
5044 |
G68 FORMAT ERROR (M series) |
5046 |
ILLEGAL PARAMETER (ST.COMP) |
5050 |
ILL–COMMAND IN CHOPPING MODE (M series) |
5051 |
M–NET CODE ERROR |
5052 |
M–NET ETX ERROR |
5053 |
M–NET CONNECT ERROR |
5054 |
M–NET RECEIVE ERROR |
5055 |
M–NET PRT/FRT ERROR |
5057 |
M–NET BOARD SYSTEM DOWN |
5058 |
G35/G36 FORMAT ERROR (T series) |
5059 |
RADIUS IS OUT OF RANGE |
5059 |
RADIUS IS OUT OF RANGE (T series) |
5060 |
ILLEGAL PARAMETER IN G02.3/G03.3 (M series) |
5061 |
ILLEGAL FORMAT IN G02.3/G03.3 (M series) |
5062 |
ILLEGAL COMMAND IN G02.3/G03.3 |
5063 |
IS NOT PRESET AFTER REF. (M series) |
5064 |
DIFFERRENT AXIS UNIT (IS–B, IS–C) |
5065 |
DIFFERENT AXIS UNIT (PMC AXIS) (M series) |
5067 |
(HPCC) (M series) |
5068 |
G31 FORMAT ERROR (M series) |
5069 |
WHL–C:ILLEGA P–DATA (M series) |
5073 |
NO DECIMAL POINT |
5074 |
ADDRESS DUPLICATION ERROR |
5082 |
DATA SERVER ERROR |
5085 |
SMOOTH IPL ERROR 1 |
5096 |
MISMATCH WAITING M–CODE |
5110 |
IMPROPER G–CODE (G05.1 G1 MODE) (M series) |
5111 |
IMPROPER MODAL G–CODE (G05.1 G1) (M series) |
5112 |
G08 CAN NOT BE COMMANDED (G05.1 G1) (M series) |
5113 |
CAN NOT ERROR IN MDI MODE (G05.1) (M series) |
5114 |
NOT STOP POSITION (G05.1 Q1) (M series) |
5115 |
SPL : ERROR (M series) |
5116 |
SPL : ERROR (M series) |
5117 |
SPL : ERROR (M series) |
5118 |
SPL : ERROR (M series) |
5122 |
ILLEGAL COMMAND IN SPIRAL (M series) |
5123 |
OVER TOLERANCE OF END POINT (M series) |
5124 |
CAN NOT COMMAND SPIRAL (M series) |
5134 |
FSSB : OPEN READY TIME OUT |
5135 |
FSSB : ERROR MODE |
5136 |
FSSB : NUMBER OF AMPS IS SMALL |
5137 |
FSSB : CONFIGURATION ERROR |
5138 |
FSSB : AXIS SETTING NOT COMPLETE |
5139 |
FSSB : ERROR |
5155 |
NOT RESTART PROGRAM BY G05 |
5156 |
ILLEGAL AXIS OPERATION (M series) |
5157 |
PARAMETER ZERO (M series) |
5195 |
DIRECTION CAN NOT BE JUDGED (T series) |
5196 |
ILLEGAL OPERATION (HPCC) (M series) |
5197 |
FSSB : OPEN TIME OUT |
5198 |
FSSB : ID DATA NOT READ |
5199 |
FINE TORQUE SENSING PARAMETER |
5212 |
SCREEN COPY : PARAMETER ERROR |
5213 |
SCREEN COPY : COMMUNICATION ERROR |
5214 |
SCREEN COPY : DATA TRANSFER ERROR |
5218 |
ILLEGAL PARAMETER (INCL. COMP) |
5219 |
CAN NOT RETURN |
5220 |
REFERENCE POINT ADJUSTMENT MODE |
5222 |
SRAM CORRECTABLE ERROR |
5227 |
FILE NOT FOUND |
5228 |
SAME NAME USED |
5229 |
WRITE PROTECTED |
5231 |
TOO MANY FILES |
5232 |
DATA OVER–FLOW |
5235 |
COMMUNICATION ERROR |
5237 |
READ ERROR |
5238 |
WRITE ERROR |
5242 |
ILLEGAL AXIS NUMBER (M series) |
5243 |
DATA OUT OF RANGE (M series) |
5244 |
TOO MANY DI ON (M series) |
5245 |
OTHER AXIS ARE COMMANDED (M series) |
5251 |
ILLEGAL PARAMETER IN G54.2 (M series) |
5252 |
ILLEGAL P COMMAND IN G54.2 (M series) |
5257 |
G41/G42 NOT ALLOWED IN MDI MODE (M series) |
5257 |
G41/G42 NOT ALLOWED IN MDI MODE (T series) |
5300 |
SET ALL OFFSET DATAS AGAIN |
5302 |
ILLEGAL COMMAND IN G68 MODE |
5303 |
TOUCH PANEL ERROR |
5306 |
MODE CHANGE ERROR |
5307 |
INTERNAL DATA OVER FLOW (M series) |
5311 |
FSSB:ILLEGAL CONNECTION |
5321 |
S–COMP. VALUE OVERFLOW |
5400 |
SPL:ILLEGAL AXIS COMMAND (M series) |
5401 |
SPL:ILLEGAL COMMAND (M series) |
5402 |
SPL:ILLEGAL AXIS MOVING (M series) |
5403 |
SPL:CAN NOT MAKE VECTOR (M series) |
5405 |
ILLEGAL PARAMETER IN G41.2/ G42.2 (M series) |
5406 |
G41.3/G40 FORMAT ERROR (M series) |
5407 |
ILLEGAL COMMAND IN G41.3 (M series) |
5408 |
G41.3 ILLEGAL START_UP (M series) |
5409 |
ILLEGAL PARAMETER IN G41.3 (M series) |
5411 |
NURBS:ILLEGAL ORDER (M series) |
5412 |
NURBS:NO KNOT COMMAND (M series) |
5413 |
NURBS:ILLEGAL AXIS COMMAND (M series) |
5414 |
NURBS:ILLEGAL KNOT (M series) |
5415 |
NURBS:ILLEGAL CANCEL (M series) |
5416 |
NURBS:ILLEGAL MODE (M series) |
5417 |
NURBS:ILLEGAL MULTI–KNOT (M series) |
5418 |
NURBS:ILLEGAL KNOT VALUE (M series) |
5420 |
ILLEGAL PARAMETER IN G43.4/ G43.5 (M series) |
5421 |
ILLEGAL COMMAND IN G43.4/ G43.5 (M series) |
5422 |
EXCESS VELOCITY IN G43.4/ G43.5 (M series) |
5425 |
ILLEGAL OFFSET VALUE (M series) |
5430 |
ILLEGAL COMMAND IN 3–D CIR (M series) |
5432 |
G02.4/G03.4 FORMAT ERROR (M series) |
5433 |
MANUAL INTERVENTION IN 3–D CIR (M series) |
5435 |
PARAMETER OUT OF RANGE (TLAC) (M series) |
5436 |
PARAMETER SETTING ERROR 1 (TLAC) (M series) |
5437 |
PARAMETER SETTING ERROR 2 (TLAC) (M series) |
5440 |
ILLEGAL DRILLING AXIS SELECTED (M series) |
5445 |
CRC:MOTION IN G39 (M series) |
5446 |
CRC:NO AVOIDANCE (M series) |
5447 |
CRC:DANGEROUS AVOIDANCE (M series) |
5448 |
CRC:INTERFERENCE TO AVD. (M series) |
5452 |
IMPROPER G–CODE (5AXIS MODE) (M series) |
5453 |
NOTE: G68 IS CANCELED (HPCC) (M series) |
5455 |
ILLEGAL ACC. PARAMETER (M series) |
4800 |
ZONE: PUNCHING INHIBITED 1 |
4801 |
ZONE: PUNCHING INHIBITED 2 |
4802 |
ZONE: PUNCHING INHIBITED 3 |
4803 |
ZONE: PUNCHING INHIBITED 4 |
4804 |
ZONE: ENTERING INHIBITED 1 +X |
4805 |
ZONE: ENTERING INHIBITED 1 –X |
4806 |
ZONE: ENTERING INHIBITED 2 +X |
4807 |
ZONE: ENTERING INHIBITED 2 –X |
4808 |
ZONE: ENTERING INHIBITED 3 +X |
4809 |
ZONE: ENTERING INHIBITED 4 +X |
4810 |
ZONE: ENTERING INHIBITED 4 –X |
4811 |
ZONE: ENTERING INHIBITED 1 +Y |
4812 |
ZONE: ENTERING INHIBITED 1 –Y |
4813 |
ZONE: ENTERING INHIBITED 2 +Y |
4814 |
ZONE: ENTERING INHIBITED 2 –Y |
4815 |
ZONE: ENTERING INHIBITED 3 +Y |
4816 |
ZONE: ENTERING INHIBITED 3 –Y |
4817 |
ZONE: ENTERING INHIBITED 4 +Y |
4818 |
ZONE: ENTERING INHIBITED 4 –Y |
4870 |
AUTO SETTING FEED ERROR |
4871 |
AUTO SETTING PIECES ERROR |
4872 |
AUTO SETTING COMMAND ERROR |